rabbitcement9

How to Replace a Saab 9-3 Key The Saab 9-3 has a good attraction for drivers. It is well-lit and has an efficient engine. It also has a top safety rating. It is crucial to have two keys that are compatible for your vehicle. If you lose one key, it could be expensive to replace it with a new one. How to replace the ignition Key on a Saab 9-3 You must change your car key if it won't turn. This guide will show how to replace the ignition key on a Saab 9-3. You'll need a replacement key, a new reprogrammable battery, and a new key-fob case. As opposed to earlier models, modern Saab cars use transponders in the key-fob instead physical key that can be used to unlock and start the vehicle. The rechargeable batteries contained in the key-fob get worn out, and eventually can't hold any charge. This is especially when you use the same key for the same lock. The good news is that the battery can be replaced easily by an experienced locksmith. saab car keys can also do it yourself if have the appropriate tools and a bit of patience. The first step involves separating the key-fob. This is done by inserting a flathead screwdriver in the slot located in the middle of the case. You will need to work slowly, as the plastic is thin and is susceptible to damage. Once the case is opened then you can prepare the new key by combining the lower portion of the old key and the transponder and banana on the new key. This will ensure that the new key is linked to the CIM properly, which could be the difference in replacing the original key for your Saab 9-3. How to replace the ignition Key in a Saab 900 If you don't have two keys you will need remove the steering wheel and dashboard in order to access the ignition. Start by disconnecting the negative battery cable. Once the battery is disconnected, you can take off the trim and dashboard pieces around the steering wheel. Once the dash has been removed, you can push an screwdriver through the hole at the back of the ignition switch and pull it out. The ignition barrel has an ignition lock that could stop the vehicle from starting if the key isn't in it. If the ignition switch on your 900 isn't working properly, check whether the key is within the lock or is stuck inside the barrel. It's also recommended to rotate your keys often and keep them clean so that they don't get bent. Saab cars differ from other cars in that they don't have traditional metal keys. Instead, the car recognizes electric signals generated by the key fob using the use of a specific microchip. If you lose your only working key fob, the dealer will charge you top dollar to replace the computer module (known as the CIM). We can reprogram the EEPROM on your current computer to make it accept new keys without having to replace it. You'll save up to 50% off the dealer's cost! This is the SAAB Key PROGRAM. Find out more about it here! How to replace the ignition Key in a Saab9-5 The metal portion of a traditional Saab key is simple to copy, and it's also not much of an impediment against theft of a vehicle. The electronic part of the key-fob is equipped with an electronic chip that detects the car when the key is inserted into the ignition switch. Saab's anti-theft device has been relying on this technology for over a decade. It's not as efficient as a physical lock for your door however, it makes the theft of your car much more difficult. This is why every Saab owner should always have a spare key on hand. Most new Saabs come with two keys at the factory. However, you can buy more keys from an authorized dealer using a handheld computer called a Tech-2. The cost can be under $400 for the transmitter+transponder (different than the metal key blade/shell that opens the doors and turns the ignition cylinder). The only exception is NG 9-3 cars, which have modern, more advanced features that require a separate key-fob and work through a different process. If you lose all keys in the event of a loss, the dealer will replace your CIM or TWICE modules and charge you a premium for it. We can reprogram your computer's EEPROM to accept new keys without having to replace expensive modules. How to replace the ignition Key on an XC90 Saab It's possible to replace your SAAB key fob if it is experiencing difficulty turning the barrel of the lock. The process is simple and you don't even need to visit a dealership. You can do it at home, using a couple of basic tools. It is first necessary to prepare the new keys. Before you start, be sure that the anti-theft system has been disabled by placing blocks on the rear wheels and releasing the handbrake. Put the key into the ignition, and then turn it to the “on” position. This will activate the accessories but not start the engine. Repeat this five times, then keep the key in the on position. Then you'll need to buy a new case for your key fob. They are readily available at many auto parts stores and are typically inexpensive. Based on the model, you may even purchase them without electronic components. To open the case simply push the flathead screwdriver into the slot in the middle. The case will split easily, and once you've done that, you'll have access to the internal electronics. To remove the electronics use a small screwdriver and attempt to pull them out in a gentle manner.